Tanks, explained
Well pressure tanks in Barrie: what to expect, what size, and why it matters for your pump
The pressure tank is the part of a well system nobody thinks about until the pump starts clicking on and off every few seconds. Here is how we handle pressure tank repair and replacement in Barrie, what happens on the visit, and the questions we answer most.
What to expect when you book a pressure tank visit
Weekdays, the $45 service call covers the trip and the diagnosis. The plumber checks the tank’s air charge with a gauge, listens to the pump cycle, tests the pressure switch cut-in and cut-out, and looks at the tee, gauge and relief valve for corrosion or weeping. In about twenty minutes we know whether the tank needs air, the switch needs setting, or the bladder has failed. You get a written price before anything is replaced. Most replacement tanks are on the truck, so a failed tank in Barrie is usually replaced on the same visit, typically in two to three hours including draining, swapping the tee and fittings, recharging and re-testing.
How fast can pressure be restored when a tank fails?
A waterlogged tank does not stop the water; it makes the pump short-cycle, which is what eventually kills the pump. If the pump is still running you have water, and a same-day or next-day visit is fine. If the tank has burst or the pump has quit, treat it as a no-water emergency: we answer those 24/7 in Barrie, after-hours billed higher and quoted before we leave the shop. Either way, the goal is normal pressure before we leave, confirmed by running taps and watching the gauge through several full cycles.
How a pressure tank protects the pump and your hydro bill
A submersible pump draws its biggest current in the first second of every start. Without a working tank it starts for every glass of water, which is hundreds of starts a day; that heat and wear is why pumps on bad tanks die early. A properly charged tank stores a few gallons under air pressure, so the pump starts a handful of times an hour instead, runs long enough to cool itself, and uses less electricity for the same water. Replacing a $600 tank on time is the cheapest pump insurance there is, and it is one of the things we check on every maintenance visit.
Which tank and what size for your home
Almost every tank we install is a bladder (diaphragm) tank: the water sits in a rubber bladder and never touches the steel, so there is no rust and no need to add air every few months the way an old galvanized tank needs. Sizing is the part people get wrong. The tank has to give the pump at least a minute of run time per cycle, so we size from the pump’s flow rate, not the size of the house. A typical Barrie home on a 10-gallon-per-minute submersible gets a tank with roughly 20 gallons of drawdown; a bigger family, a hot tub, irrigation or livestock pushes that up, and a long-run pump or a low-yield well sometimes needs two tanks. A tank that is too small does not cure short-cycling; it just moves it. We carry the common sizes and order the large ones within a day or two.
Pressure switch settings and the tank’s air charge
The tank and the switch work as a pair. The air charge in the tank must sit 2 psi below the switch’s cut-in pressure; if it drifts, the tank’s drawdown shrinks and the pump cycles more. On every visit we check the charge with the system drained and set it to match the switch, usually 38 psi for a 40/60 switch. If the house wants more pressure for a second-floor shower, we can move the switch to 50/70 only when the pump, pipe and tank are rated for it, and we tell you if they are not. A clogged switch sensing tube, pitted contacts or a sticking gauge get replaced at the same time, because a new tank with an old switch is a return visit waiting to happen.
Why licensed and insured matters for this job
A pressure tank sits on a pressurized line with electricity a foot away at the switch. A bad tee, a missing relief valve or a tank undersized for the pump is the kind of mistake that shows up as a flooded basement or a burnt pump months later. Our plumbers are licensed and insured, the work is done to the Ontario Building Code, and the tanks we install carry the manufacturer’s warranty; maintenance plan members get PHD’s 10-year warranty on major well parts we install. The plumber who quotes the job is the one who installs it and the one who answers the phone if there is a question afterward.
Questions Barrie homeowners ask about pressure tanks
How do I know my tank is waterlogged? Tap it: an empty-sounding top and a dull bottom is normal, dull all the way up means water in the air space. Also, the pump cycling every few seconds while one tap runs. Shut the pump off, drain the tank and check the charge with a tire gauge; no air or water coming out of the valve means the bladder has failed.
How long does a tank last? Ten to fifteen years for a bladder tank on clean water; less with acidic or iron-heavy water, which we test for on every well visit.
Does it have to be in the basement? No. It goes anywhere frost-free on the main line after the well, including a crawlspace, pump house or utility closet, with room to service the switch.
Is an expansion tank the same thing? No. An expansion tank is the small tank on a water heater that absorbs thermal expansion in a closed city-water system. We install those too, but a well pressure tank is a different job. Pressure switch and controls in Barrie · Low water pressure in Barrie · Well maintenance plan in Barrie